RTS Cstrunk Spezifikationen Seite 48
- Seite / 104
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
42
3. Tap PGM.
The Vol. bar graph is now monitoring the selected audio source.
4. Tap CLR to exit metering, or allow the metering function to timeout after about 1 minute.
Mixing
Mixing lets you route selected audio signals to the intercom system, to the speaker, or to the left or right headphone when
using a headset. By default, the microphone signal is routed to the matrix, and the matrix signal is routed to the speaker and to
the left and right headphones.
1. Tap PGM.
To Matrix displays. Press
↓↓
or
↑↑
to display any of the following items
To Matrix
Speaker
Left Hdst
Right Hdst
2. Tap PGM.
♦
Mic or Mic displays. If an arrow displays, this indicates the mic signal is currently routed to the destination you
selected in step 2. To toggle the selecting, press PGM. You can also press
↓↓
or
↑↑
to display any of the following
items
Mic
Matrix
Aux 1
Aux 2
3. Tap CLR to exit when you are finished changing the mixing selections.
4. Run Service Menu, Save Cfg, to store any mixing changes.
Service Menu, Hdst Sel
This item lets you select either the front panel headset jack or the headset connector on the optional rear connector module. By
default, the front panel jack is selected.
1. Select Hdst Sel, and then tap PGM.
Default displays. The arrow indicates the default front panel jack is selected.
2. Press ↓↓ or ↑↑ to change the selections.
External displays.
3. Tap PGM.
♦
External displays. This indicates the rear panel jack is now selected.
4. Tap CLR to exit.
5. Run Service Menu, Save Cfg, to store the new settings.
Service Menu, LCD Bright
This item allows you to adjust the brightness of the LCD backlighting so that the unit’s display can be viewed in a wide range
of ambient room light conditions.The All selection controls the overall LCD brightness level including the right LCD on the
KP-632. The Main selection controls the left LCD on the KP-632. The EXP1 controls the LCD on the EKP-632. Normally the
LCD brightness levels are balanced at the factory before shipping, thus under normal circumstances the All selection should
be used.
1. Select ICD Bright
,
then tap PGM.
All displays. To change the selection, press
↓↓
or
↑↑
to move through the All, Main, and EXP 1 selections.
2. Tap PGM.
If the All selection was made proceed to step 6. If Main was selected Left appears. If EXP1 was selected press
↓↓
or
↑↑
to move through the Left and Right selections.
- USER INSTRUCTIONS 1
- Contents 3
- Introduction 9
- GPI Connector Module 10
- EKP-632 Expansion Keypanel 11
- LCP-632 Level Control Panel 11
- MCP-90 Panel Microphone 12
- Headsets 12
- Installation 13
- Address Switch Setting 14
- Address Setting for Zeus 15
- Address Setting for ADAM CS 15
- Connections 16
- Power Supply Connector 17
- Headset Connector 17
- Panel Microphone Connector 18
- Basic Operation 19
- Intercom Keys and Displays 20
- Listen LED Indication 21
- Intercom Key Operation 22
- Muting the Microphone 23
- Call Waiting Operation 24
- Telephone Operation 25
- KP9X Redial Sequence 26
- KP9X Autodial Sequences 26
- Manual Dialing 27
- Autodial 28
- Display Panel ID 29
- > Tap CLR to quit 29
- 1. Tap the E-PNL key 32
- 3. Tap the PGM key 32
- • Tap COPY 35
- Clearing a Key Assignment 35
- KP-632 Menu System 37
- Menu System, Key Assign Menu 39
- Key Assign Menu, Matrix 40
- Key Assign Menu, Pt-to-Pt 40
- Key Assign Menu, Party Line 40
- Key Option Menu 43
- Key Option Menu, Key Groups 44
- Key Option Menu, Solo 44
- RVON Conn. Menu 45
- Service Menu 45
- Service Menu, Baud Rate 46
- Service Menu, Dim 46
- Service Menu, Disply Dim 46
- Service Menu, Hdst Sel 48
- Service Menu, LCD Bright 48
- Service Menu, Matrix Out 51
- Service Menu, Mic Select 51
- Service Menu, Min Volume 51
- Service Menu, Mod Assign 51
- Service Menu, Output Level 52
- Service Menu, Reset Cfg 53
- Service Menu, Save Cfg 53
- Service Menu, Scr Saver 53
- Service Menu, Sidetone 54
- Service Menu, Snoop Tally 54
- Service Menu, Test Panel 54
- Service Menu, Tone Gen 54
- Specifications 55
- Speaker Amplifier and Speaker 56
- KP9x Display Sequences 63
- KP9x Setup Page Assignment 64
- KP9x Phone Operation 65
- Menu Access 67
- Menu List 68
- Mode 2 Operation 69
- Glossary 71
- Features 77
- Dip Switches 79
- Addresses and the RVON-1 82
- Top Level Menu, Rvon Conn 84
- Basic Network Configuration 87
- Wide Area Network 89
- TABLE 4. Packet Translation 90
- TABLE 5. Packet Translation 90
- IP Addresses 92
- Ping a Computer 93
- RVON Configuration 95
- Network Terminology 96
- • Backcard DB-9 J2 98
- Press Enter 100
- 3. Press Enter 101
Verwandte Produkte und Handbücher für Türsprechanlagen RTS Cstrunk
Türsprechanlagen RTS CIF-612 Spezifikationen
(72 Seiten)
(72 Seiten)
Türsprechanlagen RTS TR-240 Spezifikationen
(86 Seiten)
(86 Seiten)
Türsprechanlagen RTS BP300 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Türsprechanlagen RTS TWI224 Bedienungsanleitung
(39 Seiten)
(39 Seiten)
Türsprechanlagen RTS TM-2000 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Türsprechanlagen RTS XCP-ADAM-MC Wartungshandbuch
(182 Seiten)
(182 Seiten)
Türsprechanlagen RTS XCP-24 Wartungshandbuch
(114 Seiten)
(114 Seiten)
Türsprechanlagen RTS MRT327 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Türsprechanlagen RTS XCP-955 Bedienungsanleitung
(49 Seiten)
(49 Seiten)
Türsprechanlagen RTS BP-325 Bedienungsanleitung
(39 Seiten)
(39 Seiten)
Türsprechanlagen RTS XCP-16-DB9-T Datenblatt
(26 Seiten)
(26 Seiten)
Türsprechanlagen RTS XCP-ADAM-MC Spezifikationen
(19 Seiten)
(19 Seiten)
Türsprechanlagen RTS TR-240 Spezifikationen
(20 Seiten)
(20 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern