RTS TM-2000 Bedienungsanleitung PDF herunterladen (Seite 29)

7.10 Keypanel Installation Notes

•

KP95/96/97 Keypanels: Refer to your keypanel

installation manual for installation information.

•

DKP-8, DKP-12, KP-12: Refer to the User Manual

for all installation and operation information. When

connecting to the intercom system, use the 9-pin

FRAME connector on the back of the unit. KP-12

only: There are two optional back panel modules: the

Rear Connector Module and the GPI Module. Refer

to the separate installation instructions supplied with

each of these modules.

•

All Keypanels: When constructing keypanel cables,

use the 9-pin intercom cable diagram in this manual

(Figure 11, page 23).

•

Zeus provides a keypanel status indicator for every

intercom channel. If there is a keypanel connected

and exchanging data with Zeus, the status indicator

will be lit. You can also use the status indicator to

check that you have correctly set the keypanel’s ID

number. For example if you know you just connected

a keypanel to port 8, but the port 7 LED turned on,

the keypanel’s ID setting is not correct.

☞

Important! KP95 / 96 / 97 series keypanels:

Always reset the keypanel after changing any of the

rear panel DIP switch settings. Do this by

momentarily turning off the AC power to the

keypanel.

7.11 TIF-951 Telephone Interface

Installation Notes

The TIF-951 has two separate phone line interfaces, and

each of these interfaces to a separate intercom port. You

can connect one or both as follows:

1. Connect phone lines to the modular phone jacks

labeled "LINE" on the back of the TIF-951.

2. A second modular jack labeled "INST" is also

provided for each phone line. This may be used to

connect a telephone or other instrument along with

the TIF-951.

3. For each connected phone line, connect from the

DE-9S connector (labeled "INTCM FRAME") on the

back of the TIF-951 to a Zeus intercom channel. Use

a 9-pin intercom cable (Figure

11, page 23).

4. For each intercom port used by the TIF-951, set DIP

switches 4 to 7 on the back of the TIF-951 as

summarized in Table 7. For all other TIF-951 DIP

switch settings, refer to the TIF-951 User Manual.

☞

Important!: Always reset the TIF-951 after

changing any of the rear panel DIP switch settings.

Do this by momentarily turning off the AC power to

the TIF-951.

•

The keypanel status indicators on the Zeus front

panel also work with the TIF-951. If there is a

TIF-951 connected to a channel and exchanging data

with Zeus, the status indicator for that channel will be

lit.

7.12 Single Audio Inputs

External audio sources, such as program feeds, can be

connected to the input pins of an intercom port. Use a ca-

ble as shown in Figure 14, page 23. The program source

should be balanced and must be DC isolated. Nominal in-

put level is +8 dBu; however, you can adjust the analog

input gain, if necessary, to compensate for nonstandard

levels. In ZEUSedit, open the System menu and point to

Gains, Analog Input / Output Gains. After you have se-

lected this item, you can press the F1 key to get setup

help.

Getting Started, Zeus™ DSP Intercom Matrix 27

1 8 16 24

The keypanel status indicators (top row). Green indicators

will be lit for every channel where a keypanel or TIF-951 is

connected and exchanging data with the intercom system.

ID Number Address DIP Switch Settings*

SW 4 SW 5 SW 6 SW 7

1 Down Up Up Up

2 Up Down Up Up

3 Down Down Up Up

4 Up Up Down Up

5 Down Up Down Up

6 Up Down Down Up

7 Down Down Down Up

8 Up Up Up Down

* Down=Closed; Up=Open

Table 7. ID DIP Switch Settings for the TIF-951

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 35 36 37

Kommentare zu diesen Handbüchern

Keine Kommentare

RTS TM-2000 Bedienungsanleitung Seite 29

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Türsprechanlagen RTS TM-2000