RTS TM-2000 Bedienungsanleitung Seite 1

TM-2000 Trunk MasterMTM-2000 Mini-Trunk MasterSWP-2000 Switch Over PanelICP-2000 Interconnect PanelUser ManualTM-2000MTM-2000ICP-2000SWP-20009350-7715

88. Trunk Master B TrunkEdit connector. Connects to COM port 2 of the TM-2000/MTM-2000 assigned to be Trunk Master B.9. Trunk Master B parallel port.

9SpecificationsTM-2000NOTE: When powering the TM-2000 unit down, press and hold the power switch for 5 seconds to turn off power.Height...

10

11CHAPTER 2InstallationInstalling SoftwareThere are two software packages that can be used with an external PC connected to the TM-2000/MTM-2000. The

12Trunking Connections and Setup1. Identify the correct wiring diagram for your system. For non-redundant TM-2000/MTM-2000 systems, use example sys-te

134. Once AZedit is restarted, click the KP button on the toolbar, and then select the port that you want to set as a trunking port: either enter the

14• Within each intercom system, assign keypanel keys as required to communicate with destinations in other intercom systems. This is similar to assig

15Licensing for the TM-2000/MTM-2000In order for the TM-2000/MTM-2000 software to operate you must have either a signed license file or a USB dongle.I

16NOTE: There are many Ethernet Adapter cards that are listed as being supported by Linux; however, in order to support any other cards, the Linux ker

17Updating the TM-2000/MTM-2000 SoftwareIn order to update the TM-2000/MTM-2000, the following files are required:update_tm.shone or more update files

PROPRIETARY NOTICEThe product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex rese

18FIGURE 8. Example of an non-redundant TM-2000 system.

19FIGURE 9. Example of a redundant TM-2000 system

20FIGURE 10. 9-pin D-sub connector pinoutsFIGURE 11. 25-pin D-sub connector pinoutFIGURE 12. 50-pin SCSI type II connector pinoutFIGURE 13. RJ-11 conn

21FIGURE 17. RJ-11 to DE-9S audio cableFIGURE 18. RJ-11 to RJ-11 audio cable.FIGURE 19. Unspecified device to RJ-11 audio cable.FIGURE 20. ICP-2000 to

22FIGURE 25. TM-2000 to TM-2000 network linking (standard networking crossover) cable.FIGURE 26. TM-2000 to SWP-2000 parallel port status and control

23Recommended Cables1. For cables using RJ-11 connections use Category 5 (CAT-5) network cable.2. For RJ-45 connectors, use CAT-5 network cable. RJ-45

25Appendix AUseful Linux TricksOn the computer console, Shift+Page Up and Shift+Page Down can be used to scroll through the last six or so screenfuls

TableofContentsDESCRIPTION AND SPECIFICATION ... 3Intr

3CHAPTER 1Description and SpecificationIntroductionThis manual describes the installation and operation of the TM-2000/MTM-2000 Trunk Master and Mini-

4Front Panel Features1. Status indicators for power, hard drive.2. Front security panel3. Cooling fans (2)4. Front Fan Filter - slide Right to take ou

5Rear Panel Features1. Power supply fan2. Power switch (rear)3. AC power connector4. Keyboard and Mouse connectors15.USB Connectors6. Serial (COM1) po

6ICP-2000 DescriptionThe ICP-2000 is a 1RU breakout panel that converts the SCSI type II connection provided from the TM-2000/MTM-2000 communication c

7Front Panel Features1. Power LED. Indicates that the SWP-2000 has power.2. TM/MTM A Status LEDs. Indications for: Activity, Active TM/MTM, Standby TM