RTS KP-12 Bedienungsanleitung PDF herunterladen (Seite 57)

KP-12 Keypanel Menu Mode 49

Bosch Security Systems, Inc.

User Manual

F.01U.193.243

Rev. 11

Procedure to Assign MODS

If the keypanel is currently displaying MD1 in the left side of the call waiting window, skip steps 1 through 3.

1. Turn the SELECT control to display MENU, then tap the SELECT control.

2. Turn the SELECT control to display SERVICE, then tap the SELECT control.

3. Turn the SELECT control to display MOD ASGN, then tap the SELECT control.

The currently assigned MOD numbers appears in the displays above the keys on the keypanel (and any connected

EKPs connected to a KP-12). Also, MD1 displays in the left side of the call waiting window. This signifies MOD1.

The right side of the call waiting window indicates where the module is currently assigned. One of the following

displays:

MAIN indicates the module is assigned to the keypanel

EXP1 indicates the module is assigned to the first expansion panel

EXP2 indicates the module is assigned to the second expansion panel

NONE indicates the module is not assigned

4. Turn the SELECT control until the MOD number you want to assign (MD1, MD2, etc.) is displayed in the left side

of the call waiting window.

5. Tap the SELECT control.

IMPORTANT: Read this instruction completely before proceeding! Turn the SELECT control to select the panel where

you want to assign the MOD, but do not tap select yet.

6. On the selected panel, identify the group of 4 keys where you want to assign the MOD.

7. Press and hold any one of these four (4) keys, then tap the SELECT control.

After a few moments, the new MOD number appears in the displays above the affected keys (if it was not displayed

before) and the call waiting window confirms the MOD has been assigned as requested by displaying the MOD

number and the panel where it was assigned.

8. Double-tap the SELECT control to return to the previous menu level, then repeat from step 5 to assign additional

MODs.

Press and hold the SELECT control for two seconds to exit menu mode.

NOTE: MOD changes are saved automatically. You do not need to run SAVE CFG.

Using Multiple Expansion Panels (KP-12 Only)

When using multiple expansion panels, some MOD numbers may have to be reassigned so that each group of four (4) keys has

its own unique MOD number. Table 6 on page 50 shows the correspondence between MOD numbers, key numbers, and setup

pages.

EXAMPLE: Connecting one (1) EKP-20 along with a KP-12. Use the default MOD numbers as shown in Table 5 on

page 48. Next, assign setup pages. See “Top Level Menu, Page (1-4)” on page 27.. You should assign

one (1) setup page as MAIN. This page corresponds to the keys on the KP-12. Assign a second setup

page as “EXP1”. This page corresponds to the first 16 keys on the EKP-20. Assign a third setup page as

“EXP2”. The first 4 keys on this setup page will correspond to the remaining 4 keys on the EKP-20. The

remaining 12 keys on the setup page are not used. If you want to connect LCPs, you can use one LCP-

12 and one LCP-20 without changing the ROMs.

EXAMPLE: Connecting two (2)EKP-20 Expansion Panels along with a KP-12. From Table 5 on page 48 you can see

that the EKP-20 has default MOD numbers 5 through 9. One of the EKPs must therefore be

reprogrammed to use MOD 10 through 14. Also, assign one setup page a “Main”. (To assign setup

pages, See “Top Level Menu, Page (1-4)” on page 27..) This page will correspond to the keys on the

KP-12. Assign a second setup page as “EXP1”. This page will correspond to the first 16 keys on the

first EKP-20. Assign a third setup page “EXP2”. The first 4 keys on this setup page will correspond to

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

RTS KP-12 Bedienungsanleitung Seite 57

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Türsprechanlagen RTS KP-12